In-Line Probe Mounting Gland w/ Compression Fitting

½" In-Line Probe Holder allows laboratory grade probes (except conductivity) to be inserted directly into new or existing PVC lines. This type of probe installation provides very accurate parameter measurements as water is continu...

Avg. Customer Review (2) reviews

Conductivity Cell (3/4 inch Slip PVC Fitting)

The Conductivity Cell consists of a ¾" In-Line Probe Holder pre-installed in a ¾ Slip x Slip x FTP PVC tee. To ensure the accuracy of the conductivity measurement, the probe must be installed either in-line or in a "drip cup" (see...

Be 1st to review

Pro Powerline Interface Module

X-10 Pro Powerline Interface The X-10 Control Interface plugs into a standard wall outlet and connects to the Octopus via a 7 ft. RJ-11 cable. The Control Interface transmitts X-10 command signals via the existing AC wiring to tu...

Be 1st to review

AquaWeb 2.0 for Win 9x/NT/2000/XP

AquaWeb 2.0 for Windows 95, 98, 2000, ME, NT, XP Allows you to communicate with your Octopus 3000, perform advanced graphical analysis of current and historical data-from just about any Windows PC.

Be 1st to review

Octopus External Modem (USA Only) Modem Cable Required

Windows Plug-n-Play external Modem. Required for any application configured for remote pager alarms or AquaWeb remote data acquisition. Modem/Ethergadget cable (63-010806) is required to connect the Modem to the Octopus. Please n...

Be 1st to review

Octopus RS-232 Modem/Ethergadget Cable (10ft)

10-ft. cable connects modem and ethergadget to the Octopus Controller. The Modem Cable is required for connecting a modem to either the Octopus or AquaNode. Due to the unique wiring configuration of this cable, non-Aquadyne cable...

Be 1st to review

Octopus Aquaweb RS-232 PC Cable

Aqua WebRS-232 PC Cable (10-ft.) The AquaWeb RS-232 PC Cable allows for a direct connection between Octopus and a Windows PC. This provides the communication link necessary for data aquisition via AquaWeb.  10 ft. cable...

Be 1st to review

Octopus - Ethernet Interface, (Ethergadget) Modem Cable Required

The Aquadyne Ethernet Terminal Server (EtherGadget) connects the Octopus Controller to Ethernet networks using the IP protocol family. Communications is established through the use of TELNET sessions between AquaWeb II and the Eth...

Be 1st to review

Octopus Power Failure Detection Switch Assembly (USA Only)

Power Failure Detection Switch with 110 VAC power supply and Mini-DIN connector. Provides audible alarm and pager alarm (optional) in the event of a power failure. For USA use only. In order for the Octopus to issue either a loca...

Be 1st to review

Octopus Level Switch Assembly

The Level Switch Assembly permits the monitoring of the water level, and triggers a local audible alarm and pager alarm (optional) in the event of a high or low condition. Switch can be installed either as normally open or normall...

Be 1st to review

Octopus Flow Switch Assembly (1.5 inch PVC Slip Fitting)

The Flow Switch Assembly allows the Octopus 3000 to detect whether flow rates are above or below a certain user adjustable level, and triggers a local audible alarm or remote pager alarm (optional). Factory adjusted to close the c...

Be 1st to review

Octopus Dual 9V Battery Backup

Dual 9V Battery Backup for Octopus Controllers

Be 1st to review

Octopus UPS Battery Backup (USA Only)

UPS Battery Backup for Octopus Controllers

Be 1st to review