1-800-566-3474

Taam Seio Electronic Controller (for Models M1100, M1500 & M2600 Only)

Read 3 Reviews Write a Review


TA3771

This item has been discontinued.

TAAM/Via Aqua

For Models: Seio M1100, M1500 & M2600 Only

CAUTION:

  • This controller is made exclusively for Seio Super Flow Pump only
  • Do not operate the SEIO controller with any other type of pump
  • All warranty will be void if this unit is used on other pumps
Features:
  • Built-in Auto High-Low Speed
  • Variable timit 15 sec. to 30 min.
  • Runs One or Two Seio Pumps
  • Auto Restart After Feeding
  • Intended for use with only SEIO water pump models: 1100, 1500, & 2600
  • The controller will control one or two SEIO Super Flow Water Pumps. The pumps can be set to go from low to high; this surge can be set from 15 seconds to 30 minutes. The pumps on low operate at approximately 50% flow and then will ramp up to 100% when on high. There are also two preset feeding buttons at 8 minutes and 16 minutes. Once the time has elapsed the unit will go back to the original preset.
  • Replaceable fuse 2.5 amp/250v
IMPORTANT INSTALLATION SAFEGUARDS AND SAFETY GUIDELINES:
  • Do not operate the SEIO controller with any other type of pump.
  • Mount controller where it will not come in contact with moisture or water.
  • Mount the controller securely above the aquarium.
  • Prior to maintenance on any electrical aquarium appliance or maintenance to the aquarium, you must disconnect all electrical aquarium devices.
  • Routine maintenance is required to ensure the maximum performance and the longevity of the controller and SEIO water pumps. See maintenance guidelines in SEIO water pump instructions.
  • The use of a surge suppressor is strongly recommended.
  • A drip loop must be used when plugging all electrical aquarium devices. The drip loop is that part of the cord which hangs below the level of the receptacle.
  • You must verify that the receptacle is clean and free of moisture at all times. The receptacle must be free of water, salt and calcium.
  • Do not deviate from the Safeguards and Safety Guidelines.
  • The national code requires that a GFCI be utilized in the branch circuit which supplies electrical power to the aquarium pump and all other electrical aquarium devices.
  • Clean the controller as needed to keep unit free of dust and all deposits.
INSTALLATION:
  1. Find a dry area to mount the controller. Secure the controller above the aquarium/water level. Area must be well ventilated. Never place controller under or inside the aquarium cabinet.
  2. Plug one or two pumps directly into the controller.
  3. While the unit is off, plug the controller into a GFCI electrical receptacle.
  4. Turn the controller ON. The screen will now read 15 and the yellow second LED will be lit.
  5. Press the set button until the desired time parameter is set. The yellow LED is for seconds and the red LED is for minutes.
  6. Once the desired time is set, press the auto button. Once set, the time screen will switch off.
  7. When feeding, press the auto button then press the desired feeding time.
Dimensions: 8.5"" L x 2.75"" W x 6.5"" H

Note: The use of two pumps does offer control on separate intervals. Both pumps are ran simultaneously.

Specifications

  • Built-in Auto High-Low Speed
  • Variable timit 15 sec. to 30 min.
  • Runs One or Two Seio Pumps
  • Auto Restart After Feeding
  • Intended for use with only SEIO water pump models: 1100, 1500, & 2600
  • The controller will control one or two SEIO Super Flow Water Pumps. The pumps can be set to go from low to high; this surge can be set from 15 seconds to 30 minutes. The pumps on low operate at approximately 50% flow and then will ramp up to 100% when on high. There are also two preset feeding buttons at 8 minutes and 16 minutes. Once the time has elapsed the unit will go back to the original preset.
  • Note: Replaceable fuse 2.5 amp/250v
  • Dimensions: 8.5"" L x 2.75"" W x 6.5"" H
  • Note: The use of two pumps does offer control on separate intervals. Both pumps are ran simultaneously.


Warranty

180 day manufacturer warranty

Steve from BEAUMONT, CA UNITED STATES

12/28/2007

Experience Level: Intermediate

No good

Unit is heavy, featureless, and packaging is devoid of adequate information. This is NOT a wavemaker, simply a massively overpriced pump controller. It will run two pumps, but both are on the same cycle at all times. There are far less expensive units with far more features and adequate documentation available. This controller is worthless.

12 out of 12 found this review helpful

Was this review helpful?

THOMAS CLARK from LOS ANGELES, CA UNITED STATES

10/25/2007

Experience Level: Expert

Inferior Product

It is hard to imagine how anyone could design such a bad and limited controller. There is no wavemaker feature per say--2 pumps can either be run at 50% or a 100%: they do not alternate.There is no nighttime feature. The time for the 50% and the 100% operation must be the same. The actual controller is bulky and looks cheap.

10 out of 10 found this review helpful

Was this review helpful?

VICTOR from COTO LAUREL, PUERTO RICO

10/22/2007

Experience Level: Expert

Problem on day 1.

Unit worked nicely for about 10 minutes, then fuse blew! I bought replacement fuses at Radio Shack and it didn't start up after that. Also, this controller doesn't oscillate speeds between the two pumps, rather, they both go from 50% to 100% simultaneously. Should have gone with a Tunze TS12.

10 out of 10 found this review helpful

Was this review helpful?