Great Aquariums Start Here
1-800-566-3474
    Free Shipping On $175+
  • FREE Shipping On $175+
  • 14-Day Low Price Guarantee
  • 14-Day Low Price Guarantee
  • Same Day Shipping
  • Same Day Shipping
FREE Shipping on Orders Over $175
FREE Shipping on
Orders Over $175
Standard ground shipping (1-7 business days) starts at a low $5.99 and most orders over $175 ship FREE. Learn More
14-Day Low Price Guarantee
If you find a product we sell for a lower price at another online store, we will match their price—today and up to 14 days after you've purchased the item! Learn More
Same Day Shipping
Same Day Shipping
We promise to ship your order as fast as humanly possible. In fact, 99% of orders placed before 6 pm EST ship the same day! Learn More

American Marine Pinpoint ORP Controller Information

  1. Overview
  2. General Specifications
  3. Displays & Adjustments
  4. Important Note on Probe Placement
  5. Adjusting the Controller Setpoints
  6. Connecting Controlled Devices
PINPOINT ORP Controller
Reef Aquarium
I. Overview

This device consists of an ORP Monitor and electronics, which control external devices, based on the ORP reading.

It is important that you understand these instructions and it is critical that you follow the cautions in this manual. Most users will be controlling the addition of ozone gas into their system with this instrument and there can be undesirable results if ozone is added to the system in an uncontrolled fashion. It is critical that one pay special attention to the placement of the ORP probe in the system. You must frequently check the condition and age of the ORP probe. Control electronics are not human, they are not intelligent and they can not "know" when something has happened to make their input or output invalid. If the probe is not immersed in the system, it will no longer be reading the correct ORP and ozone gas will be added in a completely uncontrolled fashion. Installing an ORP Controller on your system does not mean that you no longer have to pay attention to it. You must still monitor the aquarium so that you can note when a problem exists and correct it in a timely fashion. If your application is particularly critical you might consider using 2 separate PINPOINT ORP Controllers with the ozone (or other) device wired through both controllers so that BOTH devices must agree before any external device is to become activated.
top
II. General Specifications

ORP Measurement Range -1,999 to +1,999 mV
ORP Setpoint Range 0 to 1,000 mV
3 1/2 Digit LCD Display
Resolution 1 mV Unit
2 Independent 5 Amp (110 VAC) Relay Outputs
top
III. Displays and Adjustments

ORP Display
ORP Monitor Adjustment & Instrument Status
Controller Set Point Block
Display Mode
Controller Status LED¹s
110 VAC Outlets (#1 &2)
Platinum Band ORP Probe

UPPER LEFT (ORP Display)
The 3 1/2 digit LCD at the top left of the controller displays a numeric value corresponding either to the ORP, or the controller setpoints.

LOWER LEFT (ORP monitor Adjustment & Instrument Status)
The red POWER LED is illuminated when the power is turned on to the controller. The ORP LED is illuminated when the display is indicating the ORP from the probe. The ORP LED is off when the display is indicating either the high or low controller setpoints.

CENTER (Controller Setpoint Block)
There are two potentiometers that are used to adjust the controller setpoints. They control the RANGE and CENTER VALUE of the controller, respectively. Detailed information regarding their adjustment is given later in the ADJUSTING THE CONTROLLER section.

LOWER RIGHT (Display Mode)The position of the slide switch determines what the LED display will show. At the center position, the display indicates the ORP that the probe is measuring, and the red ORP LED at the lower left of the instrument will be illuminated. Sliding the switch up or down will cause the display to show the high and low controller setpoints, respectively.

UPPER RIGHT (Controller Status LED¹s)There are a total of 4 LED¹s here. The upper row shows the status of the 110 VAC outlets, which you will find, on the back of the controller beneath the LCD ORP display. The lower LED¹s are on when the display mode switch is in the HIGH or LOW position.

110 VAC OUTLETS
There are two outlets, which will be energized when the ORP is above (outlet #1) or below (outlet #2) the controller setpoints. A common application for the controller will be to control the addition of ozone gas to the system. Since the addition of ozone gas raises the ORP, an ozonizer would be plugged into the LOW control outlet (Outlet #2).

ORP Probe
An ORP electrode is supplied with the controller. As shipped, a plastic fluid-filled cap will protect the end of the electrode. Gently remove the clear plastic cap on the end of the probe by first running lukewarm water over it for a few seconds. The fluid inside the cap is a mixture of #4.0 calibration fluid + 3M KCL which is commonly known as storage fluid. There is a suction cup attached to the electrode, which may be used to secure it, or a user-devised scheme of holding the electrode may be employed. Accuracy of these ORP electrodes is considered superior and calibration of ORP electrodes is impractical and should not be attempted. Do not allow the electrode to dry out.
top
IV. Proper placement of the ORP electrode

When the controller is operational, it is critical that the tip (bottom 1-inch) of the electrode be immersed in the system at all times. If the water level falls below the lower pink band of the electrode, the ORP probe will not read properly. If the erroneously measured ORP is higher than the controller setpoint, devices connected to that outlet will remain permanently ON, irrespective of the actual ORP.

Take some time to determine how much the fluid level around the probe will fluctuate. Adjust the position of the probe accordingly.

Consider the final placement of the probe and attach it securely so that it remains in position. Be sure to check the probe position occasionally. Complacency usually sets in when you feel that "Everything is running fine".
top
V. Adjusting the controller setpoints

The PINPOINT ORP Controller is capable of controlling ORP within the range of pH 0 through 1,000 mV. After the selection of the ORP setpoint, you will find that the controller can create a span around this setpoint, both above and below, from about +/- 10 mV units to +/- 100 mV units.

Two adjustment screws in the setpoint block will determine the controller ORP setpoints. The right adjustment screw determines the "center value" or the point halfway between the high and low setpoints. Note that the Center Value is NOT directly displayed and must be calculated. The left adjustment screw controls the range both above and below the selected ORP setpoint.

As an illustration of how the two adjustments are related, consider the following:

When the measured ORP moves from the center of the acceptable ORP range to below the low setpoint, the device attached to the LOW outlet is activated and will remain ON until the ORP is brought above the center value.

Adjusting the Controller Setpoints:
  1. Determine the "Center Value" that you wish to establish and the range around this center value you feel is acceptable (between 10 and 100 mV units). Remember, if you are only adding ozone gas, you will have ORP control in only one direction.
  2. Turn the range adjustment screw to its minimum setting.
  3. Move the display mode slides switch (HIGH/READ/LOW; on the right side of the controller) between the high and low setpoints to show the ORP range presently selected. Slide the switch to the LOW position.
  4. By turning the CENTER VALUE adjustment screw with a fine blade screwdriver, adjust the lower limit to about 10 mV below the center value you have determined is best for your application.
  5. Alternately display the high and low ORP controller settings and take the average by adding the high and low setting together then dividing by 2. The result is the Center Value.
  6. Now adjust the range adjustment screw to give the desired ORP range, Again, use the display mode switch to show the high and low values. When they are acceptable to you, return the display mode switch to the READ position, and verify that the red ORP LED at the lower left corner of the instrument is ON. You have now established the controller setpoints.
top
VI. Connecting controlled devices

The PINPOINT ORP Controller is capable of driving devices to control both the high and low ORP limits of the system.

When the measured ORP is greater than that of the high ORP limit you have established, Outlet 1 will be energized which will activate a device to lower the ORP (if you so desire). When the measured ORP is lower than the low ORP limit, Outlet 2 will be energized which will activate a device to raise the ORP. There are also LED's on the front of the controller which are illuminated when the respective outlets are turned on.

You should make every effort to insure that the pumps, ozonizers or valves you attach are of good quality and checked frequently.
top
Copyright/Warranty:

PINPOINT ORP Controller by American Marine inc. is warranted to be free of defects in Material and workmanship for a period of 2 years from date of sale. Positive proof of purchase is required for warranty claim.

American Marine Inc. will not be liable for any costs of removal, installation, transportation charges, or any other charges, which may result in connection with a warranty claim.

American Marine Inc. will not be liable for any damage or wear to products or livestock caused by abnormal operating conditions, water damage, abuse, misuse, unauthorized alteration or repair or if the product was not installed in accordance with the printed operating instructions.

Any defective product to be returned must be sent freight prepaid with appropriate documentation supporting the warranty claim. Replacement or repair will be at the discretion of American Marine Inc. Typical turnaround time within 48 hours. Overnight delivery available.

This item is temporarily unavailable but will be back in stock soon.

Item #
Price:
Click the Add To Cart button below if you'd like to reserve this item today. Any other items included in your order will be immediately processed and shipped. We will ship this item separately as soon as it arrives. We will not charge you for this item until it ships and you will incur no additional shipping charges.

Enter your email address in the field below and click the Notify Me button if you'd like us to send you an email when this item becomes available. Although you will be immediately notified when we have stock on hand, we will not reserve any units for you; you must return to our website and place an order.

Your Email:
Just enter your email address below and we'll let you know when the product you are looking for becomes available!

Item Code:
Price:
Your Email:
Email Specials
Subscribe to our newsletter feed.
Newsletter Tips & Tricks! New Products!
Discounts & Promos!
Testimonials
Aug 18, 2014
"I like how easy it is to do business with Marine Depot. I also love the competitive prices on products."
Joshua

Aug 15, 2014
"The best online place to shop for all aquarium supplies. The best packing ever: I've ordered lights, nothing has ever broken."
Corals&Clowns

Aug 13, 2014
"Great place to buy reef aquarium products."
Gabe

Marine Depot Newsletter Signup
Aquariums, News & Culture
Join 100,000+ readers who receive weekly tips, videos, deals and giveaways.