Zoo Med MagClip Industrial strength MAGNETIC suction cup with interchangeable clips Never replace your suction cups again!
Includes 6 assorted sizes of nylon clips to hold all types of aquarium accessories like pH probes, ORP...
American Marine PINPOINT AC Adapter Kit™ (110vac) The AC adapter kit is optional to replace the 9-volt battery, which some monitor owners find convenient, especially for PINPOINT pH and PINPOINT ORP monitors. Note: Not comp...
3’ Male/Male AquaBus cable. Used to connect an AquaBus module (PM1, EB8, etc) to another AquaBus Module or Apex base unit.
Great for many uses: Including securing Air Lines, ATO`s, Hoses, Probes, Float Switches, Heaters, Spray Bars and Much More. The list is virtually endless.
Package includes one Mag-Tastic Aquarium Magnetic Holder
The RLSS Waveline Interface cable will allow you do connect your Apex-Ready Waveline DC pump to the VDM (variable dimming module) Ports of your Neptune Systems Apex Controller.
Once connected, you can easily program your Apex ...
15’ Male/Female AquaBus cable. Extension Aquabus cable used to lengthen AquaBus cables so that modules which are more than 15’ apart can be connect together.
Alternate Gyre Mode Modified Cable for IceCap Gyre Interface Module
This cable allows you to run your Maxspect Gyre in both forward and reverse direction by using one full Variable Speed port on your Apex to connect two 0-10v s...
2 Channel AquaSurf or Apex to stream cable assembly. It has 1 RJ45 connector which plugs into the Apex base unit, and 2 Din5 connectors which plug into 2 Tunze Controllable Stream pumps.
Authorized bus cables from Digital Aquatics for your ReefKeeper Elite system
120V AC to 12V DC Power Adapter for use on the AquaController Apex.
Very handy for UPS setups or firmware updates.
2 Channel light dimming cable for Apex variable speed ports. It has 1 RJ45 connector on one end of the cable which plugs into the Apex base unit. The other end of the 6’ cables have bare wires which connect to 0-10V di...
Advanced LED Dimming Cable for Apex VDM Module
Use this cable to connect Aqua Illuminations Sol and Acan Lighting LEDs to the VDM Module
You can have complete control over your AI Sol and supported Acan Lighting LED Ligh...
DC24 to Bare wire cable - 10’
For the DIY hobbyists out there. This cable connects to the 24VDC accessory connections on the 1LINK module. This cable has two bare (tinned) wires on the other end so you could connect it up to a ...
Switch Adapter Kit for Digital Aquatics Reef Keeper
Allows you to connect a variety of switch inputs on your SL1 and SL2 ports.
Compatible with both the ReefKeeper Elite and ReefKeeper Lite systems.
Cable Length is 6`. C...
Combination stream and light dimming cable for Apex variable speed ports. It has 1 RJ45 connector on one end of the cable which plugs into the Apex base unit. The other end of the cable contains 1 Din5 connector used t...
1LINK Male - Male cable - 10’
4-pin male to male cable many hobbyists have been waiting for. It is ten feet long. This cable allows you to connect your DOS to the 1LINK thereby eliminating the need for the DOS to be connected t...
Vertex Aquaristik’s Acrilico-Line of accessories gears towards a low profile and elegant approach to everyday aquarium maintenance needs. Crafted from polished, seamless acrylic; these accessories are easily incorporated into any ...
This 9-foot control cable allows for connection between the Neptune Apex controller and the Basic models of the Aquatic Life Halo LED Pendant Fixture (Both Freshwater & Marine)
This 9-foot control cable allows for connection between the Digital Aquatics Archon controller, or the ALC module for the ReefKeeper, and the Aquatic Life Basic models of the Halo LED Pendant Fixture (Both Freshwater & Marine)